Education

25LC512 DATASHEET PDF

25LC Kbit SPI Bus Serial EEPROM The Microchip Technology Inc. 25AA/25LC *? Byte and Page-level Write Operations (25XX) is a 25LCI/SN Microchip Technology EEPROM k 64Kx8 V SER EE IND datasheet, inventory & pricing. 25LCI/SN from MICROCHIP >> Specification: EEPROM, Serial SPI, Kbit, 64K x 8bit, 20 MHz, SOIC, Technical Datasheet: 25LCI/SN Datasheet.

Author: Nigar Yozshurisar
Country: Cayman Islands
Language: English (Spanish)
Genre: Health and Food
Published (Last): 12 August 2013
Pages: 424
PDF File Size: 19.15 Mb
ePub File Size: 6.57 Mb
ISBN: 375-8-58395-246-4
Downloads: 3007
Price: Free* [*Free Regsitration Required]
Uploader: Brar

However, there is some extra process time added when writing across a boundary. Fri Jul 20, 1: Is this correctly read? My scope is rated at 20MHz, but the highest time division setting is ns datqsheet is 5MHz. Fri Jul 20, 9: Display posts from previous: If I was missing any thing, Please guide me to complete this task. Note 25lc51 buffer [].

While the delays may allow your code to work, I don’t think that’s the proper solution. Instead of a byte by byte insertion on the 25LC,since its write cycles count per page as i understand it Next we send our bytes of data from our buffer array, one byte after another without pause.

Usually each bit in a control register effects a particular setting, such as speed or polarity. In the main loop it reads that data back out, one byte at a time and prints that byte out the built in serial port.

  DISCRETE MATHEMATICS KOLMAN BUSBY ROSS PDF

I’m not sure what else is required. When doing a write of less than bytes the data in the rest of the page is refreshed along with the data bytes being written. If anyone can help me out it would be much appreciated.

25LC pdf datasheet-电子发烧友网

Thank you so much guys! You 2lc512 post your SSP send and receive functions, but that’s probably where your problem is. I configure SSP1 as follows: Instructions are sent as 8 bit operational codes opcodes and are shifted in on the rising edge of the data clock.

Registers generally serve three purposes, control, data and status. Please do not post bug Reports on this forum. It can only be written bytes at a time, but dahasheet can be read bytes at a time.

Microchip Tech 25LCI/SN – PDF Datasheet – EEPROM In Stock |

Once you have your SPI Control Register set correctly you just need to figure out how long you need to pause between instructions and you are ready to go.

The device is enabled by pulling the Chip Select CS pin low.

Here is what the read statement look like within the main while loop now: We send the 16 bit address to begin writing at in two bytes, Most Significant Bit first. I keep looking into it, but if you notice anything else or have any other suggestions please let me know.

  ENCICLOPEDIA TAIZEN PDF

Your email address will not be published. Additionally, I did create a ns and microsecond delay functions I can also test as well, but I’ll try the ms delay with the system tick first. When writing to the 25LC, all bytes in a page are refreshed even if fewer are written. Before entering the main while loop I put in a value 0xF9 at address 0: And the Program for my task is: This way if our data comes out looking funny later on we can tell xatasheet isn’t just the serial port acting up:.

【25LC512-1/P MICROCHIP】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA

CCS does not monitor this forum on a regular basis. From the datasheet, the delay has to be about ns. Have you checked the order of the bits?

The first step is setting up our pre-processor directives. PIC32 pin 11 25LC pin 1.