Life

2N6489 DATASHEET PDF

2N 2N 2N DESCRIPTION. ·With TO package. ·Excellent safe operating area. ·Complement to type 2N 2N 2N respectively. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N datasheet, 2N circuit, 2N data sheet: MOSPEC – POWER TRANSISTORS(15A,75W),alldatasheet, datasheet, Datasheet search site for.

Author: Tahn Goshura
Country: Somalia
Language: English (Spanish)
Genre: Literature
Published (Last): 11 September 2010
Pages: 318
PDF File Size: 14.51 Mb
ePub File Size: 12.48 Mb
ISBN: 245-1-21536-894-4
Downloads: 59861
Price: Free* [*Free Regsitration Required]
Uploader: Mazuzilkree

Q3 is therefore non-conducting and the output voltage remains constant. In this situation, an opto coupler is commonly used to couple the feedback signal from the output back to the control IC. The RMS current rating is also an important consideration for input capacitors and is an example of improvements n26489 by today’s manufacturers.

First, the transistors never see more than the peak line voltage and standard V fast Switchmode transistors that are now readily available may be used. It is apparent here that the heart of the supply is really the high frequency inverter.

Internal current limit amplifier for excellent current regulation and sharp cross- over between constant voltage and constant current regulation modes. Output polarity reversal 2. Low Vio drift amplifier 2. From these designs a judgement can be made by the designer as to which regulator — circuit configuration combination best meets his requirements in terms of cost, size and complexity. In these cases a preregulator circuit, as shown in Figure C may be used.

Determine D for the heatsink shape as given in Figure and draw a line from this point through a, which was found in bto determine Typical circuit configurations for this circuit are shown on Figure All of these devices utilize the same basic circuit configuration as shown in Figure A.

A bleeder resistor is normally used here not only for safety but to mask the differences in leakage current. 26n489

2N6489 Datasheet

A guide to Motorola’s rectifier products is given in Appendix B. Aside from rather unique drive requirements, a FET is 2n6498 similar to a bipolar transistor. Switching power supply components have actually evolved from components used in similar applications. Methods for obtaining greater output currents are shown in Section 3. Basic Pulse Width Modulator Control IC Features required by a control IC vary to some extent because of the particular needs of a designer and on the circuit topology chosen.

  HUAWEI RTN 910 PDF

In fact, Vcm does influence the amplifier output voltage. C N should be a high frequency type capacitor Qq: In this circuit the voltage sensing inputs of both the internal amplifiers are tied together for sensing the overvoltage condition.

2N (Mospec) – POWER TRANSISTORS(15A,75W)

The analysis given in the earlier section on boost regulators dealt strictly with the discontinuous mode where all the energy is dumped from the choke dagasheet the transistor turns on again.

This involves checking the turns per inch of wire against the bobbin length. All of these circuits operate the magnetic element in the unipolar rather than bipolar mode. These peaks can be 5 to 15 times the value of load current. In dealing with the continuous mode, it should also be noted that the transistor must now turn-on from to V rather than V level, because there no longer is any dead time to allow the flyback voltage to settle back down to datasehet input voltage level.

Operation of the boost circuit Figure B is more subtle in that it first stores energy in 2b6489 choke and then delivers this plus energy from the input line to the load. All that is left to determine is how the chosen current limit scheme affects required pass element SOA.

Datasheets from 07 Marth

Unfortunately, this technique is datzsheet noise immune, and suffers an additional disadvantage in that it must be operated at voltages above 9. The complete circuit schematic is shown in Figure Therefore, it is important that the circuit lead lengths be short and the layout as tight as possible.

A typical good circuit layout is shown in Figure for an MCR regulator circuit configuration. There is a cost penalty here over the single transistor circuit due to the extra transistor, diode and floating base drive requirement of the upper switch transistor.

The output voltage can be externally adjusted with some accompanying loss of temperature performance; see device data sheet, Section Line Loss Detection — In addition to providing overvoltage protection, the MC can also be used to detect line loss or brownout conditions which will soon cause the power supply to fail.

For details on these services, please click the appropriate link from the menu on the left. It turns out that for most capacitors even in the so-called “low ESR” series, the output ripple depends more on this resistance than on the capacitor value itself. Second, and probably even more important, transformer saturation problems are easily minimized by use of a small coupling capacitor 2. Because the designer and component manufacturer must work as a team to bring this about, companies like Motorola that are looking to the future will continue a dialogue with designers to keep abreast with their current and future product needs.

  ARVUS LIGHTER PDF

Correct amount of secondary voltage 3. The mounting surface should be flat, smooth, free of deep scratches or burrs, and free of paint, varnish, anodization, or oxidation. Oth- erwise, the power supply, across which the SCR is connected, must be shut down to reset the crowbar. Choose a rectifier with an lo rating of 2 to 5 times the actual load. Standard Baker Clamp E. The regulator will tend to keep Vo constant by sensing any changes in Vo and trying to return it to its original value.

Since it is desirable to have as much available current as possible to drive Ql thereby lowering its gain hfe requirementsan infinitely heatsinked MCI CG is the most desirable choice. Of course, access to this point is necessary. Emitter-Base resistor in “PNP” type boost configuration too large 2. Total resistance of secondary and any external resistors to be equal to Rs found from Figures-3, and -4 see Part C. The voltage drops in the high current carrying leads now have no effect on the load voltage, Vl.

The resulting output current- voltage characteristic is shown in Figure B. If problems do occur, the trouble can be traced to a design error in Output voltage adjustable to zero volts. The forward converter family which includes the push-pull and half bridge circuits evolved from the buck regulator Figure A.

When higher output drive currents are required for single-ended operation, Ql and Q2 may be connected in parallel, and the output mode control pin must be tied to ground to disable the flip-flop. This stored energy becomes the reverse bias drive when the pulse from the transformer is terminated.