The LiquidCrystal library allows you to control LCD displays that are compatible with the Hitachi HD driver. Demonstrates the use a 16×2 LCD display. □TN. □FSTN. ☑FSTN Negative. LCD type. □STN Yellow Green. □STN Gray. □ STN Blue Negative. View direction. ☑6 O’clock. □12 O’clock. A-1 LCD Module Specification Ver 2. 1. 0 FEATURES. • Display Mode: STN, BLUB. • Display Formate: 16 Character x 2 Line. • Viewing Direction: 6 O’.

Author: Moogugal Meztishicage
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Software
Published (Last): 1 October 2004
Pages: 180
PDF File Size: 2.51 Mb
ePub File Size: 7.4 Mb
ISBN: 773-1-77026-914-9
Downloads: 65676
Price: Free* [*Free Regsitration Required]
Uploader: Malamuro

This example sketch prints “Hello World! Arduino based GPS receiver.

16 x 2 LCD Datasheet | 16×2 Character LCD Module PINOUT

Virgin Galactic — Commercial Space Flight. The states of these pins high or low are the bits that you’re writing to a register when you write, or the values you’re reading when you read. The process of controlling the display involves putting the data that form the image of what you want to display into the data registers, then putting instructions in the instruction register. The LiquidCrystal Library simplifies this for you so you don’t need to know the low-level instructions. A 16×2 LCD means it can display afficheue characters per line and there are 2 such lines.

LCD Liquid Crystal Display screen is an electronic display module and find a wide range of applications.


Low to write to the register; High to read from the register. The Hitachi-compatible LCDs can be controlled in two modes: Selects command register when low; and data register when high.

To wire your LCD screen to your board, connect the following pins: A command is an instruction given to LCD to do a predefined task like initializing it, clearing its screen, setting the cursor position, controlling display etc. A ohm resistor is used to power the backlight of the display, usually on pin 15 and 16 of the LCD connector.

Kit Backpack USB + Série avec Afficheur LCD 16×2 RGB – rétroéclairé – négatif

The interface consists of the following pins:. The data register stores the data to be displayed on the LCD. The command register stores the command instructions given to the LCD. Choosing Motor For Robots. For displaying text on the screen, you can do most everything in 4-bit mode, so example shows how to control a 2×16 LCD in 4-bit mode.


Arduino – HelloWorld

You can select either the data register, which holds what goes on the screen, or an instruction register, which is where the LCD’s controller looks for instructions on what to do next. Supply voltage; 5V 4. These modules are preferred over seven segments and other multi segment LED 16d2.


SPI Module of Arduino. Before wiring the LCD screen to your Arduino or Genuino board we suggest to solder a pin header strip to the 14 or 16 afficheuf count connector of the LCD screen, as you can see in the image above. What is Web Browser. Interface SD Card with Arduino. In this LCD each character is displayed in 5×7 pixel matrix. Interface GPS with Arduino.

A ohm resistor is used to power the backlight of the display, usually on pin 15 and 16 of the LCD connector click the images to enlarge. This high-density System-in-Package SiP integrates controller, power switches, and support components. For more circuit examples, see the Fritzing project page.

Click to learn more about internal structure of a LCD. This sketch prints “Hello World! The LCDs have a parallel interface, meaning that the microcontroller has to affichdur several interface pins at once to control the display. Contrast adjustment; through a variable resistor. Choosing Battery for Robots.

There are many of them out there, and you can usually tell them by the pin interface.