Relationship

EUROSEC CPX INSTALLATION MANUAL PDF

Wire the LCD RKP as shown in the wiring section of this manual. Replace the .. The Eurosec CP8 LCD has two log modes. These are: a). gardtec eurosec cpx installation manual · Home · Blog · About · Press · Contact · Home · Blog · About · Press · Contact. Powered by カスタマイズ可能なテンプレート . A range of alarm system user guides and manuals for owners and clients. Accenta 6 · Euro 46 User Manual · Euro Mini User Guide · Eurosec CP7/CP8 LED .

Author: Voodook Kerr
Country: Philippines
Language: English (Spanish)
Genre: Medical
Published (Last): 10 January 2005
Pages: 402
PDF File Size: 4.97 Mb
ePub File Size: 9.84 Mb
ISBN: 550-5-87845-701-3
Downloads: 5442
Price: Free* [*Free Regsitration Required]
Uploader: Mikarisar

Servicing may also be a requirement of you durosec policy. This will be displayed as Keypad x Tamper and will require a valid User Code entry to stop the sounders. Under no circumstances should the actual user code be written down.

If you wish to accept the name shown press Yes and jump to step 13 Code Type. To initiate the Remote Call follow the instructions below. At this point the system will revert to battery back-up The battery will only have a limited insttallation that it can sustane the system for. I’ve forgotten my password.

EUROSEC CP8 Manuals

The CPX is capable of using two methods to activate the Duress signal. All Zones ON 2 Enter the code again to abort the setting 3 The system eurosfc now reset 15 Time will count down Or If a higher level of code is required one of the following displays will be shown: I have linked the unused zone and it seems to be working fine. Iinstallation viewing the Log, Pressing NO will move back to the previous event. You should also note that a Code Level of Control may never Set the system.

About – gardtec eurosec cpx installation manual

If this option has been invoked by your installation company the Set or Unset Status will only be displayed for ten seconds when the system is Set or Unset. Biased To set the system with a biased keyswitch, insert the key and turn it then return the manul to the original position and remove.

  HIPOVITAMINOSIS A EN TORTUGAS PDF

To do so press Yes within ten seconds. In this instance using will send a Duress code to your central station when you Set or Unset your system. Follow the normal instructions for programming codes. Control Allows an output that has been pre-programmed by the installation company to be operated. Chime is Off ok? G-Tag conforms fully with the requirements of this legislation relating to confirmed alarms on entry.

It is important that your security system is serviced on a regular basis on order that it continues to comply with the legislation. Instqllation Tampers The full security system is tampered, any attempt to remove covers from Keypads, Control Panel, Keypads, Bell Box es or detectors will cause a tamper alarm.

Before Vo-Comm can work several options will need to be programmed. Wait until the exit tone finishes before leaving. Follow the instructions from step 3 above.

Please refer to the Using G-Tag section for instructions. The alarm may be silenced by entering a valid User Code. Keypad Tamper The keypad will monitor the number keys that are pressed without a valid User Code being entered.

In the event of a sustained power cut the system battery will continue to supply the system until the battery voltage falls to a set point, at his stage the display will show: OR Press No display will show: If your system has remote communications fitted your installation company may have programmed the system so that you initialise the Access Remote call usually on lines with incoming calls barred.

Please take time to familiarise yourself with the type of equipment fitted to your premises as it will prove invaluable whilst using this manual. These may be changed at any time via a Master level code.

Please log in to reply. You currently have javascript disabled. Then choose Can or Cant Unset dependant on your requirements. G-Tag Proximity Tags may be used for setting and unsetting the system. If you do not choose to Set or Unset the system within the ten seconds the top line of the display will be blanked out and the code entry will be invalidated.

  AN INTRODUCTION TO COPULAS NELSEN PDF

A rising tone will be heard that indicates that the call has been acknowledged. My order number is if you could kindly send me the engineer manual please. Do you want to. Setting or Unsetting the system using the code that is programmed as User 7 will activate a Duress signal.

Your installation company will give training on the use of the equipment in order to comply with the relevant standards and will be able to answer specific questions about your system, request for pcx or new staff training should be directed to your installation company.

I mean do some kind of connection or make any changes through the keypad?

Duress option s must be turned cpxx by your installation company. The term Open relates to the system being Unset. If you do not acknowledge the call or hear the rising tone the Vo-Comm will repeat the message several times and then go on to dial the remaining telephone numbers until the call is acknowledged. Pressing YES will move forward to the next event.

Eurosec CPX User guide – Home Security Systems |

Before attempting to reset your system ensure that the system is Un-set. If the system was Set a full alarm will be generated. This may be in addition to or instead of central station communications. Press Yes Year is ok? Duress Codes may also be used on this system for activating Personal Alarms P. To Part 1 Set your security system press Yes twice the display will show: