Life

FX1N HARDWARE MANUAL PDF

and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.

Author: Zule Tora
Country: Algeria
Language: English (Spanish)
Genre: Career
Published (Last): 16 August 2015
Pages: 390
PDF File Size: 17.24 Mb
ePub File Size: 6.48 Mb
ISBN: 319-3-71239-857-9
Downloads: 56632
Price: Free* [*Free Regsitration Required]
Uploader: Samujin

Remove the base unit top cover. All layouts are diagrammatic and are only intended to aid the creation of wiring diagrams. D, D M ref. Do not use this terminal Fuse Surge absorbing Diode. Screw terminals must be secured to prevent a loose connection from causing a malfunction. AC Wor ld spec. Please note that the over current induced by in-rush greatly reduces the relay contacts service life.

FX0N series extension units do not have CE certification. Do not remove this screw. B Optional equipment connector port.

Associated Manuals The following manuals are recomended as esential reference material for the correct operation of a FX1N series Programmable controller. If a response time of 0. Circuit protector or fuse?

Mitsubishi FX1N-24MT-DSS Manuals

Please refer to the table below. Secure top cover with M3 screw E. Upper pot, D read from VR1. Hardwaree capacitor backed memory will retain programs for a maximum of 10 days, and requires 30 minutes to recharge upon power up. If the current leakage is greater than the stated value, then add Rb. Input circuit power supply?

  DOBBY SHEDDING MECHANISM PDF

Mitsubishi FX1NMT-DSS Manuals

See equation 2 for Rb calculation. C M3 screw to secure top cover. It should be read and understood before attempting to install or use the unit. To release, pull the spring loaded clips away from the rail and slide the unit up and off. This manual is subject to change without notice.

Check the output LEDs for operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.

Do not run input signals in the same multicore cable as output signals or allow them to share the same wire. The definition of such mahual person or persons is as follows; a Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this manual should be of a competent nature, trained manua, qualified to the local and national standards required to fulfill that role.

Software warning 4 Indicates special care must be taken when using this element of software.

Note all counters are latched Remarks C0 to C15 Type: If resistance Rp is less than the stated value, then add Rb. Hardwaee should not be installed in areas subject to the following conditions: The following instructions are also not suitable. See equation 1 for Rb calculation. The value depends on the switch setting.

  2N6489 DATASHEET PDF

When the products associated with this manual are used as a system or individually, they must be installed in a suitable enclosure. Only one board can be used at any hardwsre time, do not try to stack multiple boards. For improved response times use a ‘dummy’ resistor, see the figure below.

FX1N Hardware Manual_图文_百度文库

PL E xtension block? For greater detail, specifications and wiring examples for each optional unit, please see the relevant product manuals. These engineers should also be trained in the mahual and maintenance of the completed product. Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.

All maintenance should be carried out in accordance with established safety practices.